Post Buy Requirement
OM
.Selangor., Malaysia
Add Review

Our Products

Ophthalmic Lens Coating Machine

The box-type ophthalmic lens coating system is designed to provide AR-Coating on ophthalmic lenses. The unit can be installed in clean, dry rooms of vacuum labs or vacuum coating workshops.
View Complete Details

Combined Cleaning System

  • ELECTRICAL SUPPLY 400V, 3j (20A per phase) – 50/60 Hz
  • TOTAL POWER RATING 13 KW
  • WATER SUPPLY ½” BSP
  • OVERALL SIZE 4000mm X 1200mm X
Automation is unique with no moving parts over the process stages
3 ultrasonic cleaning stages plus ultrasonic DI water rinsing
- The filtration is configured with surface over-flow to remove surface debris
All cleaning and rinse stages have automatic level control
Clean only facility for mineral lenses
Primer stage enables PC and factory hard coated lenses to be recoated
Primer is followed by a dedicated dryer
Sloping tanks for ease of maintenance
Solvent vapour sensor for ATEX safety
Simple, single button process selection
Walking beam mass transfer with facility to bypass process tanks
There are 3 coating tanks and enables up to four coating tanks to be specified so that the coatings can be index-matched and primer-based to the lenses
Up to 190 pcs per hour
Speed profiling ( thickness control )
View Complete Details

BPI Turbo Tinter 4

  • Weight 32.68kg ( 72lbs )
  • Tanks 4 Tanks
  • Tanks size 1.5L ( 1.58qts )
BPI Turbo Tinters tint high index, hard coats and polycarbonate lenses better and faster than conventional systems. The lenses are heated by IR light from the ceramic heating chambers. (Except BPI Turbo 6, which utilizes transfer fluid). This method of heating causes the surface of the lenses to be heated higher than boiling point allowing better and more even tint penetration. The tint is kept in constant motion by the automatic stirring mechanism. The computer maintains a steady temperature ( 2) in each tank.
View Complete Details

BPI Stainless Steel Frame Warmer

  • Power Supply 100 to 240V 50/60Hz
  • Dimension L286 x W210 x H172mm
  • Weight 16.8Kg
The BPI Stainless Steel Frame Warmer is a stand-alone unit designed for the counter-top. It is a bead type frame warmer with an all stainless steel construction. (The beads are included with the unit). The power control allows a temperature range of 130 to 230F. (54 to 110C)
The temperature control dial has three main settings, these correspond to:
* HIGH. Approximately 230F. (110C)
* MEDIUM. Approximately 190F. (88C)
* LOW. Approximately 130F (54C)
The low setting is used for most plastic frames. Other setting in between HIGH, MEDIUM and LOW will allow other temperatures to be set. The unit is not restricted to the 3 main settings.
View Complete Details

Alloy Blocker

  • Weight 36Kg (79.2lbs)
With centering device, centre marker for blocking is not need for mould and RX plano.
-Adoption of circular system of coolant water shortens the time of solidification of alloy to raise productivity.
-Two station type is standard. One station type is optional.
View Complete Details

Laser Marker

  • Weight 130Kg
  • Max Operating Temp 40°C
The LensMark III is based on the unique LensMark technology which is used in
more than 100 LensMark II systems around the world. The LensMark III uses a CO2
laser with an improved power stability which, along with other technological
innovation, improves the engraving repeatability significantly.
View Complete Details

Combined Cleaning Machine

  • Electrical Supply 400V, 3 j N & E (16A per phase). – 50/60Hz
  • Lens Size 30 – 95 mm diameter
Extremely high market leading first pass yields.
- Automation is unique with no moving parts over the process stages.
- Three ultrasonic cleaning stages plus ultrasonic deionised water rinsing.
- The filtration is configured with surface over-flow to remove surface debris.
- Automatic fill and lever control all cleaning and rinse tanks.
- 2 or 3 dip coat stages (2 for index & 1 primer) 4th stage control optional.
- Automatic level control on lacquer tanks. (Optional)
- Clean only facility for mineral lenses.
- Primer stage for polycarbonate lenses.
- Sloping tanks for easy and efficient draining.
- Solvent vapour sensor for ATEX safety
- Simple, single button process selection
- Walking beam Mass transfer with facility to bypass process tanks.
- Pre curing stage with IR radiation.
View Complete Details

BPI Hot Air Frame Warmer

  • Power Supply 100 to 240V 50/60Hz
  • Dimension L152 x W350 x H229mm
  • Weight 7.7Kg
The BPI Hot Air Frame Warmer II is a stand-alone unit designed for the counter-top. It is easy to use and easy to control! It has a thermostat for unlimited temperature settings. Frames can be warmed and adjusted in only a few seconds. Solidly constructed from stainless steel and powder-coated aluminum for long life.
The BPI Hot Air Frame Warmer II has a main ONOFF switch for the whole instrument, plus a second switch that turns the heaters on and off. The temperature of the unit can be adjusted with a power control dial. For normal operation of the unit, turn on the main switch, This will turn on the fan and cool air will start circulating. To heat up the system, turn the heater switch on and adjust the thermostat dial to the desired setting.
View Complete Details

Optotech ASM Machine

Ideal start-up machine for optical freeform production
2 spindle generator
Fast pre-processing due to a PCD cutter
Sintered diamond tool for the fine cut
Superb form accuracy and very little sub surface damaging. Moreover the lenses don't have a problem spot at the center due to optimized raster kinematics
The inexpensive, efficient design of the machine gives rise to an unrivaled price-to-performance ratio
Accessories: Axis Adjuster, Coolant Unit, Recooling Unit, Barcode Hand Scanner, Remote Diagnosis, Interface
View Complete Details

Laminar Flow Box

  • Working table size 1500 mm x 545 mm x 600 mm - L x W x H
  • Centrifugal Fan 220 V AC Single Phase, 50 Hz
A laminar flow box is a carefully enclosed bench designed to prevent contamination of semiconductor wafers, biological samples, or any particle sensitive device. Air is drawn through a HEPA filter and blown in a very smooth, laminar flow towards the user. The cabinet is usually made of stainless steel with no gaps or joints where spores might collect.

Such hoods exist in both horizontal and vertical configurations, and there are many different types of cabinets with a variety of airflow patterns and acceptable uses.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Mona Eswari (Optic Mediplus Asia Supplier)
  • No,1,Jln Pahlawan 1a/3,Bandar Mahkota Cheras, .Selangor., Malaysia
  • Share us via