Intekma Engineering Sdn. Bhd.

kuantan, Malaysia

• Weight900 gr
• Case dimensions200 mm х 178 mm х 36 mm
• DisplayColor TFT with back light

Sensor Units In the VIBRO-LASER 5M sensor units the latest digital data processing technology is used. Sensor units have CCD-detectors of 30 mm. This provides you with exact and stable measuring results and allows the system to be more interference-immune from the external factors (stray light, vibration, heat flow and etc.).

• Frequency range1Hz to 10kHz, accuracy ±0.5%
• Output range10mV to 10,000mV RMS; 10pC to 10,000pC

MSC-1015 is a battery operated instrument that is used to electronically simulate variety of outputs from various types of sensors. MSC-1015 uses a menu-driven 4×16 character LCD display to establish appropriate settings. The key panel contains five sealed switches marked with arrows, E (Enter), Back and ONOFF. Power is supplied from 4 AA rechargeable, internally mounted Ni-MH batteries which can be recharged with a regulated 9Vdc source. Connection to PC is established over the front mounted LEMO connector. PC mode will be automatically started after inserting proper cable into device. Output signal is user selectable from: single-ended voltage (mV), single-ended charge (pC), differential charge (pC), current-sinking IEPE (ICP®), loop powered current source (mA), tachometer (TTL), flow (TTL), OSO® (Optical Speed Output) and BOV (Bias Output Voltage). Frequency range is 1Hz to 10kHz; RMS output voltage is from 10mV to 10V or 10pC to 10.000pC. Outputs can be provided in acceleration, velocity, displacement, voltage or charge.

• Temperature:-10°C to +65°C

PC-100 Proximity Probe Checker is a battery operated, easy to use instrument which checks sensor GAP and then indicates it on the LED bar integrated on the front panel. There is also a LCD screen for displaying GAP voltage for better accuracy. PC-100 can also be used to simulate any current sensor with constant current output. Power is supplied by one internally mounted 9V alkaline battery. Working mode can be selected by a side switch mounted on the left side. There is also a visual identification of the selected mode placed on the front panel. The measured voltage is displayed on LCD screen and on LED diodes, which indicates the position of proximity sensor. It is especially designed for fast checking of proximity probes used in the monitoring system. It also helps the operator to set up proximity probe in optimal position andor to get information about the probe position in front of the shaft. In CURRENT SOURCE mode, the instrument produces fixed current of 12mA. It is designed to get external 24V on this input and it generates fixed current through integrated current loop.

• Frequency160Hz
• Dimension150mm x 80mm x 30mm
• 160Hz0.5kg typical

SC-100 Sensor Checker is a battery operated, easy to use instrument for checking sensor condition by measuring bias voltage and for electronically simulating IEPE sensor output from accelerometers. Power is supplied by one internally mounted 9V alkaline battery. There is also a LED indication of low battery. Working mode can be selected by a side switch mounted on the left side. There is also a visual identification of the selected mode placed on the front panel. Depending on the bias voltage, the following predefined statuses are possible: In BOV TEST mode user can read measured bias voltage on the screen and sensor status on the LED diodes on the front panel. There are predefines sensor status which are depending from the bias voltage and they are: short circuit, sensor ok and open circuit. For short circuit, measured bias voltage is below 7V. For open circuit measured bias voltage is more than 15V. For sensor ok, measured bias voltage is between 7V and 15V. If the customer wants different voltage levels, changes are possible free of charge before shipment.

• Weight0.5kg typical
• Dimension196mm x 100mm x 40mm

MSS – 1010 is a battery operated instrument that is used to electronically simulate variety of outputs from various types of accelerometers. MSS-1010 uses a menu-driven 4×16 character LCD display to establish appropriate settings. The key panel contains five sealed switches marked with arrows, E (Enter), Back and ONOFF. Power is supplied by 4AA internally mounted rechargeable Ni-MH batteries, which can be recharged with a regulated 9Vdc source. Connection to PC is established over the front mounted LEMO connector. PC mode will be automatically started after inserting proper cable into device. Output signal is user selectable from: single-ended napon (mV), single-ended ®charge (pC), differental charge (pC), current-sinking IEPE (ICP), tachometer (TTL), ®flow (TTL), OSO (Optical Speed Output) and BOV (Bias Output Voltage).

• Temperature135°C
• Memory:4 MB for data

The A4900 Vibrio M is avaliable in an Ex version. All basic vibro-diagnostics measurements are available: Overall Values, FFT Spectrum, Time signal, Frequency bands, Route measurement and Expert system for automatic fault source detection. You can listen to the signal with the headphones supplied with every unit.