Post Buy Requirement
Hung Ta Instrument (M) Sdn Bhd
Seremban, Malaysia
Verified Add Review

Our Products

  1. Industrial Machinery 9 Products available
  2. Separators & Strainers 5 Products available
  3. Machines And Equipments 3 Products available
  4. Material Testing Equipment 6 Products available
  5. Testing Equipments 21 Products available
  6. Viscosity Instruments 4 Products available
  7. Hardness Tester 28 Products available
  8. Testing Equipment 8 Products available
  9. Others 20 Products available

Other Products / Services

Image Automatically Measuring Software

The Image Automatically Measuring Software, which we bring to you stands out of all others on counts of longevity and reliability. We are a top-notch Manufacturer and Supplier of Image Automatically Measuring Software from Malaysia. We offer the Automatic Measuring Software at the cost-effective prices, Place the order and get to know!

More about Image Automatically Measuring Software :

  • The measurement and control of the tester system is to use high resolution image device, display the indentation clearly on the computer screen. Through the software for signal conversion, it automatically measures the hardness value of indentation. By designated and continuous testing process, it can draw the depth and gradient curve diagram. It is supported for WIN9X, WIN7, WIN2000, WINXP operating system. The micro Vickers, Knoop and carburizing layer can be tested. Hardness value can be carried out various forms of automatic conversion. You can choose high or low magnification objective lens according to your need. Image definition: > 540lines. It can regulate the contrast and brightness of the image, can respectively open, store or print the image files and data files. You can view the data files and image files any time, and print the data files by the form of tables and curves. The computer automatic measurement system can also be connected with our company's manufacturing DHV-1000, XHV-1000, MHV-1000 and HVS-5/10/30/50 types of digital   Micro / Vickers hardness testers. This instrument besides the original instrument configuration also equips with special nozzle, a CCD camera, computer, printer, image acquisition card, image test software, encryption locks.

 

  • It can be used for the continuous experiment of continuous indentation reading after continuous loading, and can be carried out consecutive trials in each loading and each indentation reading. It is equipped with a CCD camera and video lines easy to observe, and can directly observe and measure the indentation on the display, and it has high accuracy for mouse control. For test conditions of setting, the results can be clearly and conveniently operated and displayed. By measuring software, it is conveniently operated through the computer, and can achieve a single point measurement and random multipoint measurement, data statistical measurement, arbitrary two-point or multipoint measurement for the spacing layer depth. It can be measured along the X or Y two direction, automatically carry out the calculation of infiltration depth, statistical calculations, conversion, display curve, judging whether qualified according to user input decision value ( such as 550). It is also capable of measuring length and angle of the parts and graphic preservation or printing. It can be used as a small-sized projector.


CCD Automatically Measuring Configuration is as follows :

  • Halcon image capture card : one
  • Computer : Lenovo; Hard disk: 160G; Memory: 1G; 19 inch LCD screen (Wide screen); (HP or Lenovo) color ink jet printer: one Hardware key : one
  • Camera device : one
  • Measuring software (Chinese or English) : one
  • 1.5× adapter : one
View Complete Details

Coating Thickness Gauge

Owing to our rich industry experience, we are enlisted among the preeminent Manufacturers and Suppliers of Coating Thickness Gauges from Malaysia. The Coating Thickness Gauges offered by us are manufactured using innovative technology. Our experts carry out various quality-tests on the Gauges before the final dispatch. Bulk orders of the Gauges are processed by us as per the specific requirements of the buyers.

Specifications


Download Detail File : Click Here
View Complete Details

HS PA20-F Phased Array Ultrasonic Detector

  • Display Size 10.4 inch 24 color display
  • Resolution 1024*768
  • Data storage Integrated 32GB , external USB drive can be stored directly
  • Extended Port USB2.0×2, 100M/1000M LAN×1, VGA×1
  • Encoder Port 1 (Support two encoder connections)
  • Alarm 1
  • Working temperature 0 - 40℃
  • Storage temperature -20℃ - 65℃
  • Power Supply Mode AC220 DC15V AC adapter, 11.1V Lithium battery
  • Working hours 4 hours (Single Battery)
  • Size 340×290×105 (mm)
  • Weight 4.7Kg (Battery included)

Ultrasonic phased array is a combination of ultrasonic probe chip, arranged by a number of piezoelectric chip according to a certain regular distribution, and then sequentially by a predetermined delay time to stimulate the various wafers, all the ultrasonic waves emitted by the chip to form a whole wavefront, in order to achieve beam displacement, beam deflection and beam focusing and other characteristics, to achieve a variety of testing purposes.

Ultrasonic phased array technology has nearly 20 years of development history. Early mainly used in the medical field. Initially, the complexity of the system, the complexity of the wave propagation in solids, and the high cost of cost make it limited for use in industrial non-destructive testing. However, with the rapid development of electronic technology and computer technology, ultrasonic phased array technology is gradually applied to various industries such as industrial non-destructive testing, boilers, pressure vessels, railways, aerospace, petroleum and petrochemicals, electric power and universities.

Performance

  • 128 Receive /64transmit channel phased array, digital to analog conversion support concurrent 64-channel operation, real-time phase control
  • Combined Phased array, TOFD, A-Scan into one unit, key switch and free verification. easy to detect flaws
  • Brand new procedural operation mode, easy to learn and use, easy to generate curve.
  • The simulation function of multiple workpiece structure, make defect display intuitive and clear. (Use for detection for flat weld, "T" type weld, fillet weld, pipe welding, forging, metal plate, shaft, wheel rims and other workpieces)
  • The simulation function of CAD Import of weld model.
  • Integrated the function of sector scan flip welding seam
  • Support for linear scanning, serial scan, sector scan, dual crystal scan (one sending, one receiving) scan, two-dimensional focusing scan and other scan modes;
  • Coupling monitoring function
  • Set display function of C-scan area
  • Up to 60Hz display refresh rate, better graphic dynamic effect
  • Full angle DAC curve generating and dB correction function.
  • Entirely dynamic focusing makes performance better.
  • Automatic alarm function for high gate and sound path gate, more efficient defect identification.
  • Support the function of the full trip scan and record of encoder


Phased Array Function Parameter

  • The number of element - 64/128
  • Bandwidth - 0.5-15MHz (-3dB)
  • Digital frequency - 100MHz 8bit
  • Digital sampling point - 8192
  • Digital smoothing average - 16
  • S-scan harness- 256
  • Repetition frequency - 1.0KHz-5.0KHz
  • Display refresh rate - Up to60Hz
  • Delay line precision - 2.5ns
  • Detection mode - Positive detection, negative detection, full detection, radio frequency
  • Launch delay range - 0-20us
  • Transmitting voltage - 50V-100V
  • Pulse width - 30ns-500ns (step10ns)
  • Pulse transmit mode - Negative square wave
  • Gain range - Analog gain0 - 80 dB
  • Digital gain - 0 - 30 dB
  • Gain stepping - Analog gain 0.1 dB, digital gain 6 dB
  • DAC - 16 point
  • TCG - 16point
  • Focusing - Transmit single point focusing and receive dynamic focusing
  • Scanning image - A/C/D/S/L


TOFD Module parameters

  • Bandwidth - 0.5-15MHz (-3dB)
  • Digital frequency - 100MHz 10bit
  • Digital sampling point - 1024
  • Digital averaging - 16
  • Repetition frequency -100Hz-1KHz
  • Display refresh rate - Up to 60Hz
  • Detection mode -  Positive detection, negative detection, full detection, radio wave
  • Transmitting voltage - 50V-350V
  • Pulse width - 30ns-500ns,   (step 10ns)
  • Impedance matching - 25Ω-500Ω
  • Pulse excitation mode - Negative square wave
  • Gain range - 110 dB, Minimum adjustment precision 0.1 dB
View Complete Details

Embedded Test Fixture

Because of the variety of test objects, the appearance is not the same, there are some square and round; some short and long; so often encountered different problemsin setup. After the customer provides the object for the measurement and mapping, we can manufacturein full compliance with any test items and can overcome the difficulties on the installation. This product can be customized according to needs.

View Complete Details

Quick Clamp Fixture

Suitable for application in the production line, and with the rapid clamp, can be repeated for the same product for several tests.The advantages of rapid clamp itself can significantly shorten both the time to install the test items, and the education and training hour. So there are some advantages that make easy to use, quick to get started and shorten the installation time. This product can be customized according to needs.

View Complete Details

Intermittence Testing Device

A high efficient, reliable, and trustworthy device for quality control of all connectors, terminals, cables, buttons, relays, switches and other components, the device is designed as a good helper, so that the rate is no longer a problem.

View Complete Details

HT-2811T3 Tire Rim Endurance Testing Machine

  • Min. Order (MOQ) 1 Piece(s)
  • Type Multi Functional
  • Condition New
  • Performance Optimum

Our storage facility is laced with all the modern amenities, required for maintaining high quality of the products. Also, we upgrade it on regular intervals to meet defined industry standards. Deeply rooted in NSB(Malaysia), we are indulged in the process of providing products to any required destination with ease.

View Complete Details

HS 700 Portable Ultrasonic Detector

  • Pulse Type Negative square wave pulse
  • Pulse Front <10 ns
  • Pulse Width 50 ns-500ns continuously adjustable
  • Impedance Matching 50Ω /500Ω adjustable
  • Sampling Frequency/Digits 400MHz/10bits
  • Sampling Depth 512
  • Repetition Frequency 15-1000Hz adjustable
  • Curve detection mode Digital
  • Precision of Attenuator <+1dB/12dB
  • Gain Range 0dB - 120dB
  • Sound Velocity Range 300~20000 m/s
  • Dynamic Range ≥30dB
  • Signal Bandwidth 0.5MHz - 25MHz
  • Vertical Linearity error ≤3%
  • Horizontal Linearity ≤0.3%
  • Resolution >36dB
  • Surplus Sensitivity >60dB(depth 200mmΦ2 flat-bottom hole)
  • Output WIFI USB2.0 VGA
  • Control Front panel sealed keyboard, shuttle, and touch screen
  • Size 266×164×45 mm including battery
  • Power Supply and Voltage Lithium Battery 8.4v10Ah continuously work for 8 hours
  • Environment Temperature (-10-40)℃ (reference value)
  • Relative Humidity (20-95)%RH
  • Weight About 1.5kg including battery

HS 700 Portable Ultrasonic Detector is a 400MHz hardware sampling frequency, with a higher degree of waveform reduction. It can connect to the Internet through WIFI to achieve cloud detection, GSM positioning, remote real-time positioning via mobile phone APP, resistive touch screen, oil-proof and waterproof. Touch sensitive, touch-screenable instrument with B-scan detection function.

Performance

  • 400Mhz sampling frequency Higher reduction degree
  • Connect to Internet through WIFI , reach the cloud detection
  • GSM Global Positioning , capable of real-time positioning by mobile phone APP
  • Resistive touch screen, resistant of water and oil, sensitive touch
  • With encoder B scan detection function

 

Technical parameters

  • Transmit Pulse voltage
  • Curve Display Mode Radio-frequency wave, wave demodulation (whole wave, negative and positive half wave demodulation)
  • Display Screen : Highlight true color 640×480 Daylight readable LCD, Maximum A scan size  115.2×86.4 mm
View Complete Details

Ultrasonic Thickness Gauge

Ultrasonic Thickness Gauge that we offer is manufactured and tested using the latest techniques with the objective of eliminating each and every possibility of defect. We are counted among the top Manufacturers and Suppliers of Ultrasonic Thickness Gauge. Our well-equipped production unit has enabled us to produce Ultrasonic Thickness Gauge in bulk at a time. Few words that better describe our gauge are strong in construction, corrosion resistant and dimensionally accurate.

Specifications

Measuring Range 0.75mm~300.0mm(0.03inch~11.8inch)
Units Metric/Imperial unit selectable
Sound Velocity Range 1000m/s~9999m/s (0.039~0.394in/μs
Display resolution 0.01mm or 0.1mm (lower than 100.0mm), 0.1mm (more than 99.99mm)
Accuracy  +/-(0.5%Thickness+0.04)mm, (depends on Materials and conditions)
Data Memory 5 files(up to 100 values for each file)of stored values, 5 Sound Velocity of stored values
Power Source 2pcs 1.5V AA size,batteries.250 hours typical operating time(LED backlight off)
Outline Dimensions 150mm*74mm*32mm
Workpiece surface temperature 10 ~ 60
The minimum thickness value capture capacity With a minimum thickness value capture capacity
Measurement cycle 4 times/SEC, scanning of single point measurement model 20 times per second.
Weight 238 g
Power source Type AA alkaline battery 1.5 V (2)
View Complete Details

HT-8052 Salt Spray Tester

  • Condition New
  • Tank capacity 251 salt solution
  • Spray tube warranty testing 2000 hours
  • Use Used to test the corrosion resistance of all kinds of metals

Technical Data

Model HT-8052A HT-8052A HT-8052C
Test temperature 35 ±1 /50 ±1 Deg. Cel 35 ±1 /50 ±1 Deg. Cel 35 ±1 /50 ±1 Deg. Cel
Inside dimension (cm) 160 x 100 x 50 (W x H x L) 90 x 60 x 50 (W x H x L) 60 x 40 x 45 (W x H x L)
Test specimen 15/30 Deg. 136PCS/136PCS 48PCS/30PCS 24PCS/15PCS
Power consumption 220V1Ø15KW 220V1Ø6KW 220V1Ø3KW

Graph


Download Detail File : Click Here
View Complete Details

Salt Spray Tester

(a) TEST TEMP. : 351C AND 501C
(b) INSIDE DIMENSIONS (CM) : 60 x 40 x 45
( W x H x L )
(c) TEST SPECIMEN : -
(i) 15 : 24 PCS
(ii) 30 : 15 PCS
(d) POWER : 220V
(e) POWER CONSUMPTION : 220V, 1, 3KW
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Mr. Jackie Koh (Hung Ta Instrument (M) Sdn Bhd)
  • 109 , Taman AST, Jalan Sungai Ujong, Seremban - 70200, Malaysia
  • Share us via