Post Buy Requirement
CC
selangor, Malaysia
Add Review

Our Products

Guinard Centrifudge

The GUINARD continuous centrifuge is provided with a cone cover (upper casing plus lower casing) and a sludge inlet and separated liquid outlet on its cylindrical frame. In the casing, there is a rotating cone basket in which a multiple slitted screen is provided. Moreover, the scraper, a spiral blade placed on the cone rotor, turns coaxially with the basket inside the screen. The screen and scraper, while keeping a proper clearance, rotate at a constant relative rate in the same direction.

This rate is obtainable by using change gear. The above operation is performed through the V-belt using the motor on the motor base that is incorporated in the frame. Slurry fed from the slurry inlet disperses into thin layers on the inside of the cone screen. Solid particles are scraped using a scraper rotation mechanism and dehydrated with downward motion, and then discharged into the frame. The separated liquid is transmitted through the screen slits by centrifugal force and discharged from the separated liquid outlet. When the separated solid matter needs washing, washing liquid should be supplied from the washing liquid inlet.
View Complete Details

HS Type

General Purpose Type With High Treatment Capacity


The most versatile of screw decanter type centrifuges, used in a wide range of fields.
View Complete Details

DP Type Energy-saving Centrifuges

DP Type

Energy-saving DP centrifuges that are particularly strong in the dehydration of organic sludge.
View Complete Details

ISC-H Type Centrifudge Thickener

Applications :

-Sewage and community plants

Primary setting pond sludge, mixture sludge and mixture sludge after gravity concentration, activated sludge and others (tertiary treatment sludge).

-Human excrement treatment

Activated sludge, digested sludge, mixture sludge (digested sludge plus activated sludge), purifier sludge and others (tertiary treatment sludge).

-Others

Various types of industrial waste water sludge, service water sludge and process liquid.
View Complete Details

TP-Type

Three-phase Separation of Oil, Water and Solid Matter in One Step

One unit is sufficient for three-phase separation of oil, water and solid matter.
This contribute significantly to saving energy and simple process.
Separation of such slurry would be difficult unless high centrifugal force is applied.
Since high centrifugal effect can be obtained by the IHI screw decanter, it can display excellent performance in three-phase separation.
View Complete Details

HV Type Pressure-tight Decanter

Sealed and pressure-tight

A pressure-tight and airtight decanter. It can be used for dehydration in various fields, including for hazardous materials such as solvents or poisonous substances

Features

Non-contact shaft seal method
Due to the non-contact gas seal, there is no loss of power from the seal and contamination will not occur. Futhermore, the non-contact seal ensures a long lifespan. Also, flushing liquid, necessary for mechanical type contact seal methods and the refrigeration or circulation equipment needed for it are not required.
It used an extremely low amount of seal gas as well.
View Complete Details

Turbo Generator Set

Renergy Single Stage Back Pressure Steam Turbine
High Efficiency Design

RENERGY Single Stage Turbine (RESST) are specifically designed based on API 611 & partial 612 requirements for heavy duty cycle operations with priorities for safety, reliability and high efficiency. Suitable for mechanical drives and for low voltage generators up to 3500 Kw. RESST turbines are of impulse type single stage two row Curtis blades with one row of steam reversing blades located in between the two rows of rotating blades.


All Foundation Stool Footings of the Turbine, Gearbox and Generator Mating surface are milled to surface flatness of < 0.001 thou or < 0.02 mm to mat the milled mounting pedestals surface of Turbine, Gearbox and Generator to ensure no stress or bending of the Equipments housings that might distort the geometry alignment of the bearing housings which will shorten the operation lifespan of bearings and equipments resulting unnecessary downtime and maintenance costs.
View Complete Details

Fundabac Filter

Structure of Fundabac Filter

Fundabac consists of three major parts:filter vessel, candles, (filter elements) and register pipes. The filter vessel made of stainless steel or carbon steel, with a rubber of titanium lining. The filter element are made of synthetic resins such as reinforced polypropylene resin (PPR), polyvinylidene fluoride resin (PVDF) or stainless steel, and the filter fabric is made of synthetic fiber such as polyester, polypropylene, polyphenylene sulfide (PPS), nylon or Telfon.

Principle of Filtration

Filtration

Raw liquid is pressurized and fed into the filter vessel using a pump. The filtered liquid is collected from the filtered liquid outlet for each register pipe at the top of the filter vessel.

Cake discharge

Cake attached to candles (filter elements) is dried by air and collected in solid form from the bottom of the filter vessel using back blow. The cake can also be collected in slurry form using back washing.
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • KH Yeong (Custom Craft (M) Sdn. Bhd.)
  • malaysia, selangor - 00000, Malaysia
  • Share us via